PPWR in Force: What Metal Food Packaging Must Meet Since 12 August 2026, and What Comes Next

Since 12 August 2026 the Packaging and Packaging Waste Regulation (EU) 2025/40 applies directly in every EU member state, and Directive 94/62/EC is repealed, apart from a few provisions with later end dates. For a food company that fills metal cans, the main obligations live now are the 100 mg/kg limit on four heavy metals, the PFAS limits for food-contact packaging, technical documentation with an EU declaration of conformity, a batch or type identifier plus the manufacturer’s name and postal address on the packaging, and national producer-responsibility registration. Other requirements come later: limits on empty space in sales packaging from 12 February 2028, the harmonised sorting label from 12 August 2028 at the earliest, and recyclability grades and packaging minimisation from 2030. In most cases the legal “manufacturer” of a filled can is not the can maker but the brand owner who fills it.


Until August the work had a deadline to aim at. That date has passed. What is left is a regulation that applies in full, some parts of which have no practical content yet because the Commission has not adopted the acts that fill them in.

That gap is where most of the confusion now sits. Some buyers assume nothing has changed because the label, the recyclability grades and the new producer registers do not exist yet. Others assume everything applies at once. Neither is right. Below is what applies to metal food packaging today, what does not apply yet, and what you need from your can supplier to show compliance.


What changed on 12 August 2026

The Packaging Directive of 1994 had to be transposed into national law, so every country implemented it in its own way. The PPWR is a regulation: it applies directly, in the same wording, in all 27 member states. Article 70 repeals Directive 94/62/EC with effect from 12 August 2026. A few of its provisions survive for a transition period: the old marking provision, member-state targets and reporting, and the packaging minimisation requirement, the last of which continues to apply until the end of 2029.

References to the old directive in national law and in contracts are now read as references to the regulation, using the correlation table in Annex XIII. If a specification, supplier agreement or audit checklist still cites “Directive 94/62/EC”, it is not void, but it is out of date and should be updated at the next revision.

Two documents explain how the Commission reads the regulation:

  • The Commission guidance notice C/2026/3084, published in the Official Journal on 10 June 2026, covering definitions, the PFAS rules, the date of the recyclability requirement and labelling.
  • The Commission’s PPWR FAQ, second edition, published on 3 August 2026, with a new section on enforcement in the first months.

Neither is legally binding, but both show how the Commission expects the rules to be applied.


Who is the “manufacturer” of a filled food can

This is the question that decides who signs the paperwork, and for food cans the answer is usually not the can maker.

The PPWR defines the manufacturer as the person who manufactures packaging or a packaged product, or who has it designed or manufactured under its own name or trademark. The Commission’s guidance notice applies this to sales packaging:

“In other words, for sales and grouped packaging, the manufacturer will normally be the filler, who is often also the product brand owner.”

The notice adds that there is only one manufacturer in a supply chain. For a canned food product sold under your brand, that is normally you. The can maker is a supplier: under Article 16 it must give you all the information and documentation you need to demonstrate conformity, and the FAQ states that suppliers “can therefore not refuse to provide” it.

There is one exception. If the brand owner is a micro-enterprise (fewer than 10 employees and no more than EUR 2 million in turnover or balance sheet total) and the packaging supplier is in the same member state, the supplier becomes the manufacturer. A can maker supplying a small local cannery in its own country may therefore carry the manufacturer’s obligations itself.

For private label the logic is the same: the company whose name or trademark is on the can is the manufacturer, whoever physically filled it.


What applies now

Obligation Where in the PPWR Applies from What it means for a canned food line
Heavy metals: lead, cadmium, mercury and hexavalent chromium together ≤ 100 mg/kg Art. 5(4) 12 August 2026 (already required under the Directive) Evidence for the whole can: body, ends, coatings, inks
PFAS limits for food-contact packaging Art. 5(5) 12 August 2026 Statement covering coatings, compounds, lubricants and inks
Minimisation of substances of concern Art. 5(1) 12 August 2026 Assessed in line with EN 13428:2004 until a new standard exists
Packaging must be recyclable Art. 6(1) 12 August 2026, under the old Directive criteria No grade yet; EN 13430 remains the reference
Technical documentation and EU declaration of conformity Art. 15, 38, 39; Annexes VII and VIII 12 August 2026 One declaration per packaging type, kept for 5 years
Type, batch or serial number on the packaging Art. 15(5) 12 August 2026 Can or end coding usually covers it
Manufacturer’s name and postal address on the packaging or via a QR code Art. 15(6) 12 August 2026 Accompanying document only where it cannot be placed on the pack
Producer registration in each country of sale Art. 44 and national law Existing national systems continue New harmonised registers come later

Heavy metals: an old rule with a new article number

Article 5(4) reads:

“Without prejudice to the restrictions on chemicals set out in Annex XVII to Regulation (EC) No 1907/2006 or, where applicable, to the restrictions and specific measures on food-contact materials and articles in Regulation (EC) No 1935/2004, the sum of the concentrations of lead, cadmium, mercury and hexavalent chromium resulting from substances present in packaging or packaging components shall not exceed 100 mg/kg.”

The Commission’s FAQ is explicit that “this is not a new obligation”: the same limit was in Article 11 of the Directive. What is new is that compliance has to be shown in the technical documentation, and the FAQ recommends the CEN report CR 13695-1:2000 for measuring and verifying the four metals. The derogation for recycled glass in Decision 2001/171/EC still applies, but there is no equivalent for metal packaging.

For tinplate, the question buyers usually raise is hexavalent chromium from passivation. thyssenkrupp Rasselstein states that chromium trioxide is used only during production and is not found on the surface of the finished tinplate, and APEAL members are moving to a chromium-free passivation alternative (CFPA). According to the company’s press release, the REACH authorisation for chromium trioxide runs until 21 October 2027 for tinplate passivation and until 31 December 2028 for chromium-coated steel (ECCS/TFS). Ask that the heavy-metals statement for your cans names the passivation type, so the evidence does not need redoing when the mill switches.

PFAS: limits on the whole packaging unit

From 12 August 2026 food-contact packaging may not be placed on the market if it contains PFAS at or above 25 ppb for any single PFAS measured by targeted analysis, 250 ppb for the sum of targeted PFAS, or 50 ppm for total PFAS including polymeric PFAS. If total fluorine exceeds 50 mg/kg, the chemical supplier must, on request, show how much of the fluorine is PFAS.

Two points from the FAQ matter for cans. The limits apply to the packaging unit as a whole, “including the associated inks, varnishes, glues and adhesives”. And they cover PFAS whether added intentionally or present as contamination, although preliminary laboratory results cited by the Commission found only packaging with intentionally added PFAS above the limits. For a can, the statement you need should therefore cover the internal lacquer, the external varnish and inks, the end sealing compound and any lubricants used in forming, not only the steel or aluminium.

The guidance notice recommends that authorities check step by step, starting with total fluorine. If total fluorine is below 50 mg/kg, the sample can be considered compliant, and according to the Commission every sample that passed this first step also passed the more specific tests. A total fluorine result for each coating and compound is therefore the most useful single piece of evidence to request.

There is no stock-exhaustion transition for this rule. The notice confirms that food-contact packaging placed on the market after 12 August 2026 has to meet the limits, even if it was produced earlier, while packaging placed on the market before that date may stay on the market. It also explains that sales packaging for food is normally placed on the market when it is filled. Empty cans bought before 12 August 2026 and filled after it therefore have to meet the limits.

Recyclability: required now, graded later

Article 6(1) says, without a date:

“All packaging placed on the market shall be recyclable.”

The Commission reads this as applying from 12 August 2026. But the criteria that will define “recyclable” do not exist yet: the design-for-recycling delegated act is due by 1 January 2028, and the recyclability grades A, B and C apply from 1 January 2030 or 24 months after that act enters into force, whichever is later. Until then, according to the guidance notice, manufacturers must meet only the old Directive requirements and the related standards, such as EN 13430:2004, and do not need to run the PPWR conformity assessment for recyclability.

Steel and aluminium cans are collected and recycled across the EU, so this is rarely a practical risk for the can body. It is worth watching for components: once the grades apply, labels, sleeves and plastic overcaps are assessed too, as integrated or separate components of the packaging unit (Article 6(9)).

Identification and contact details

All packaging placed on the market after 12 August 2026 must carry a type, batch or serial number, and the manufacturer’s name, registered trade name or trademark and postal address, on the pack or through a QR code or other data carrier. For a food can, the batch code on the can or the end usually satisfies the first requirement, and the name and address are normally already on the label. The FAQ allows two exceptions: an accompanying document where the information cannot physically be placed on the packaging, and an accompanying document for packaging produced before 12 August 2026 that was still in stock on that date. Stock produced before the date does not have to be destroyed or relabelled.

Documentation and the declaration of conformity

Before placing packaging on the market, the manufacturer must carry out the conformity assessment in Annex VII (Module A, internal production control), draw up technical documentation and sign an EU declaration of conformity following the model in Annex VIII. The documentation and declaration must be kept for five years for single-use packaging. We cover the declaration line by line, with a checklist of what to request from the can supplier, in a separate article: the EU declaration of conformity for metal food cans.

Producer registration and EPR

Producer responsibility fees are still national and so is registration, for now. Article 44 requires every member state to set up a register of producers within 18 months of the Commission’s implementing act on registration and reporting formats. That act was due by 12 February 2026 and had not been adopted when the regulation became applicable. The FAQ expects the first reports under the harmonised rules by 1 June 2030. Until then, existing national systems continue. What this means for fees in 2027 country by country is covered in EPR fees on metal packaging in 2027.


What does not apply yet

Date What starts Article
31 December 2026 Commission report on substances of concern in packaging, which may lead to new restrictions Art. 5(2)
12 February 2027 Member states’ rules on penalties must be in place Art. 68
1 January 2028 Design-for-recycling delegated act due Art. 6(4)
12 February 2028 Fillers of sales packaging must reduce empty space to the minimum; for food that needs headspace, compliance is assessed at the fill level at filling, and protective gases do not count as empty space Art. 24(4)
12 August 2028, or 24 months after the implementing act Harmonised sorting label on packaging Art. 12(1)
1 January 2030, or 24 months after the delegated act Recyclability grades A–C become a condition for market access Art. 6(3)
1 January 2030 Packaging minimisation by weight and volume Art. 10
1 January 2030, or 3 years after the methodology act 50% maximum empty-space ratio in grouped, transport and e-commerce packaging Art. 24(1)
1 January 2035, or 5 years after the methodology act “Recycled at scale” requirement Art. 6(2)(b)
1 January 2038 Only grades A and B may be placed on the market Art. 6(3)

Two points on this table. The sorting label depends on an implementing act that was due by 12 August 2026 and had not been adopted when the regulation became applicable, as Packaging Europe reported on 20 August. The label date is 12 August 2028 or 24 months after that act enters into force, whichever is later, so each month of delay pushes it back. Do not redesign can labels around pictograms that have not been published. Until 12 August 2028 the material codes of Decision 97/129/EC remain allowed on a voluntary basis, and national sorting labels have to give way to the EU label once it applies.

Deposit-return obligations in Article 50 concern beverage containers, not food cans. They matter to a canned food business only if it also sells drinks in cans.


Country notes

Italy. The national framework built around CONAI continues. The question Italian buyers ask most is what replaced Directive 94/62/EC. The answer is the regulation itself, directly applicable, with Annex XIII mapping old references to new articles. The heavy-metals limit Italian buyers ask about is the same 100 mg/kg as before. The CONAI environmental contribution for steel and aluminium packaging is unchanged for 2026; see the EPR article for 2027.

Latvia. The State Environmental Service confirms that, until new national legislation enters into force, the existing rules continue to apply. Latvia does not yet have a separate packaging producer register, and the State Environmental Service does not issue EPR or PPWR registration numbers. Companies placing 300 kg or more of packaging on the market each year must take part in a producer responsibility system, which also exempts them from the natural resources tax on packaging. Amendments to the Packaging Law to integrate the PPWR are being prepared.

Germany. The Packaging Law Implementation Act (VerpackDG), published in the Federal Law Gazette on 17 July 2026, replaced the Packaging Act (VerpackG) on 12 August 2026. Registration with the Central Agency Packaging Register (ZSVR) and the obligation to join a dual system for household packaging continue. Fines for breaches of directly applicable PPWR obligations start from 12 February 2027, after six months’ grace.


How enforcement starts

The FAQ adds a section on the first months after 12 August 2026. Its starting point is that enforcement “should not disrupt trade flows, supply chains or consumer access to goods”. For the formal breaches listed in Article 62, such as a missing or incorrect declaration of conformity, incomplete technical documentation or missing manufacturer details on the packaging, the authority must first require the economic operator to correct them. Withdrawal or recall comes only if the non-compliance persists. The Commission asks authorities to support operators with information requests and reasonable deadlines rather than start with sanctions.

This is not a reason to wait. A request from an authority comes with a deadline: under Article 15(10) the manufacturer must provide the documentation within 10 days. If the technical file for a can format does not exist, that is not enough time to build it with a supplier.


What to ask your can supplier now

Article 16 obliges the supplier to provide what you need. In practice, ask for the following for each can and end format you buy:

  1. A heavy-metals statement for the complete can and end, with the measurement basis (CR 13695-1:2000 or equivalent) and the passivation type of the steel.
  2. A PFAS statement covering the internal lacquer, external varnish and inks, end sealing compound and lubricants, with total fluorine results if a component exceeds 50 mg/kg.
  3. A materials specification: substrate (tinplate, ECCS/TFS or aluminium alloy), coating systems and compound, with drawings.
  4. The declaration of compliance for food contact under Regulation (EC) No 1935/2004 and, for coatings, Article 8 of Regulation (EU) 2024/3190 on bisphenols.
  5. A recyclability statement against EN 13430:2004 until the PPWR delegated act exists, and a commitment to provide the PPWR recyclability grade once it does.
  6. How the can or end is identified: the batch or type code and where it is applied.
  7. A named contact and a turnaround time for authority requests, given the 10-day limit.

The answers go into your technical documentation, and your declaration of conformity rests on them.


Frequently asked questions

Is Directive 94/62/EC still in force?
No. It was repealed with effect from 12 August 2026 by Article 70 of Regulation (EU) 2025/40, apart from a few provisions with later end dates. References to the Directive are read as references to the regulation using the correlation table in Annex XIII.

Who signs the EU declaration of conformity for a filled food can?
The manufacturer, which for sales packaging is normally the filler or brand owner, not the can maker. The can maker must supply the information and documentation needed. The exception is a micro-enterprise brand owner buying from a can maker in the same member state: then the can maker is the manufacturer.

What is the heavy-metals limit for metal cans under the PPWR?
The sum of lead, cadmium, mercury and hexavalent chromium must not exceed 100 mg/kg (Article 5(4)). It is the same limit as under the old Directive, and it applies to the whole packaging, including coatings and inks.

Do the PFAS limits apply to cans?
Yes, to all food-contact packaging placed on the market from 12 August 2026: 25 ppb for any single PFAS, 250 ppb for the sum of targeted PFAS and 50 ppm for total PFAS. They apply to the whole packaging unit, including varnishes and inks.

When does the harmonised sorting label become mandatory?
From 12 August 2028, or 24 months after the Commission’s implementing act enters into force, whichever is later. That act had not been adopted when the regulation became applicable.

Do metal food cans need a recyclability grade now?
No. The obligation to be recyclable applies, but grades A, B and C only apply from 1 January 2030 or 24 months after the design-for-recycling delegated act, whichever is later. Until then the old Directive criteria and EN 13430 apply.


Sources and primary references

A note on the quotations. Passages from Regulation (EU) 2025/40 and from Commission Notice C/2026/3084 are reproduced from the official language version of each act, so the wording in each language edition of this article is the wording published in the Official Journal. The FAQ is published in English only; passages from it are translated. In the Russian edition all quotations are an unofficial translation, because the European Union does not issue Russian-language versions of its acts, and the English original governs.

This article is general guidance, not legal advice. Who counts as the manufacturer, and which requirements apply, depends on the facts of each product and supply chain.

Request Basket