Easy-Open Ends for Food Cans: Types, Size Codes and How to Specify the Right End

An easy-open end (EOE) is a can end that opens without a tool: either a scored metal panel with a riveted tab or ring or, in a peel-off end, a heat-sealed membrane. Choosing one comes down to five decisions: the size code, which must match the can body and the seamer (211, 300, 307, 401 and so on); the opening type (full aperture, partial aperture, peel-off membrane or a beverage tab); the material (tinplate, tin-free steel or aluminium); the coatings and compound suited to the product and its heat process; and the documents your supplier has to provide under EU food-contact rules and the PPWR. The size code is easy to misread. It gives the diameter of the finished can over the double seam in inches and sixteenths, so converting it to millimetres does not give the figure end makers list: a 307 can is about 87 mm over the seam, while the 307 end is listed at 83.3 mm. Two ends with the same code from different suppliers are also not automatically interchangeable on your seamer.


It is tempting to specify the end by copying the last order. That works until something changes: a new supplier, a new product in the same can, a move to a peel-off end, a new retort programme. Then the details that were never written down (curl diameter, countersink depth, lacquer, compound, retort limits) decide whether the line runs.

Below: what an EOE consists of, how to read the size code, which opening type suits which product, how to choose the material, what has to match your can and seamer, the EU rules that apply to ends, and what to send a supplier when you ask for a quote.


What an easy-open end is made of

An easy-open end starts as a plain end shell. To make it easy-open, the end maker scores a line around the opening panel, forms a rivet from the panel itself and fixes a tab or ring to it. Pulling the tab breaks the score and the panel tears away. A peel-off end works differently: a plain end has its centre removed and an aluminium membrane is heat-sealed to the remaining ring.

Part What it does Why it matters when you buy
Shell The end body, in tinplate, tin-free steel or aluminium Sets strength, corrosion behaviour and whether the can stays one metal
Score A partial-depth cut that defines the opening Controls opening force and resistance to pressure and abuse
Rivet and tab (or ring) The rivet is formed from the panel; the tab is made separately from coated strip and fixed to it Together with the score, sets how easy the end is to open
Curl The rolled outer edge that becomes the cover hook of the double seam Must match the can flange and your seaming set-up
Countersink The recess where the seamer chuck sits Its depth and profile must match the chuck
Sealing compound A lining inside the curl that seals the double seam It is a food-contact component and has to suit the heat process
Internal and external coatings Lacquer on the food side, varnish or print outside Chosen per product; covered by the bisphenol rules

The other end of a three-piece can, the one the can maker seams on before delivery, is usually a plain bottom end (also called a sanitary end). It needs the same matching and documentation, just without the opening feature. Our range of bottom ends runs from 200 to 603 plus the rectangular club format.


How to read the size code

Can and end sizes are named with a convention from the North American can industry. In a three-digit code, the first digit is whole inches and the next two are sixteenths of an inch. So a 307 × 409 can is 3 7/16 inches across and 4 9/16 inches tall. The diameter in this convention is measured over the double seam, on the outside of the finished can.

Metric can names, used in Europe, usually refer to something different: the inside diameter of the body. That is why the same can appears under two names that do not convert into each other. A 307 can measures about 87 mm over the seam, but in Europe it is an 83 mm can. In the same way, a 211 can is a 65 mm can in metric terms, and a 603 can is a 153 mm can.

End makers use the inch code as the trade name of the end and publish a nominal diameter in millimetres next to it. Those millimetre figures are also not a conversion of the code. Our catalogue uses the figures below.

End code Nominal diameter in our catalogue European can diameter it fits Our product
200 49.5 mm about 50 mm EOE 200
202 52.5 mm 52 mm EOE 202
209 62.5 mm about 63 mm EOE 209
211 65.3 mm 65 mm EOE 211
214 69.9 mm about 70 mm EOE 214
300 72.9 mm 73 mm EOE 300
307 83.3 mm 83 mm EOE 307
401 98.9 mm 99 mm EOE 401
404 105 mm about 105 mm EOE 404
502 126.5 mm 127 mm EOE 502 for dry products
603 153 mm 153 mm EOE 603

Two practical rules follow:

  1. Order by code and drawing, never by a converted number. Send the end maker your can body specification or ask for the end drawing, and check the curl and countersink dimensions against what your line runs today.
  2. Non-round ends follow a different system. Rectangular “club” ends and oval ends carry codes such as F304, F311 or T501, usually listed with the long and short axes in millimetres. The digits in these codes are not inches and sixteenths: an F304 end, for example, measures about 97 × 51 mm. In our range these are the club ends 304 and 311.

Opening types and where each one fits

Opening type How it opens Fits best Watch out for
Full aperture (FA) The whole centre panel tears out along the score Fish and seafood, meat, vegetables, fruit and pet food; also dry products A cut edge remains on the can; check the safety edge design on the end you buy
Partial aperture Only part of the panel opens, leaving a pouring opening Pourable products such as condensed milk or oils Not suitable where whole pieces must come out
Stay-on tab (SOT) and ring-pull (RPT) beverage ends A small aperture for drinking or pouring Juices, coffee, protein and other drinks Beverage ends are aluminium and designed for drink cans and their pressures
Peel-off end (POE) An aluminium membrane, heat-sealed to a metal ring, is peeled away Milk powder, coffee, nuts and dry foods; retortable versions for wet food and pet food No metal panel edge after opening, but retort conditions must suit the membrane
Combo ends Steel ends for milk-powder cans; our catalogue lists 401 and 502 Milk powder Ask for the drawing to see how the closure works, and specify any overcap together with the end

In our catalogue, full-aperture food ends are in the canned food EOE category, partial-aperture options include the EOE 300 SOT, a stay-on-tab end used for condensed milk, and beverage ends run from 113 to 307. Peel-off ends are split by use: retortable food, milk powder and dried food. Combination ends for milk powder are in combo EOE.

Peel-off ends and the retort

Peel-off ends for wet food have to survive the same sterilisation as the can. The membrane is the weak point: as the can heats up, the pressure inside rises, and when cooling starts the pressure in the retort can fall faster than the pressure in the can. Foil-membrane ends have therefore been processed with overpressure in the retort, which reduces the load on the membrane. Page, Edwards and May also describe a newer design of peelable end that withstands full heat processes without overpressure.

Rigid steel cans with a steel end, by contrast, can usually be heated in saturated steam without overpressure, although pressure still matters during cooling. So moving a product from a steel EOE to a peel-off end can be a retort question as well as a packaging question. Before you switch, ask the end supplier for the process limits of the specific peel-off end (maximum temperature, time and whether overpressure is required) and check them against your retort and its programme.

For dry products such as milk powder, coffee or nuts there is no retort, and the choice between a peel-off end and a full-aperture aluminium end is about access, safety and reclosing. Our dried food EOE and aluminium full-aperture ends for dry products cover this side.


Tinplate, tin-free steel or aluminium

Material Typical use for ends Strengths Points to check
Tinplate (ETP) Food EOE and bottom ends Strong, retortable, magnetic, goes to the steel recycling stream with the can Internal lacquer and passivation of the steel
Tin-free steel (TFS, also called ECCS) Food EOE and bottom ends, often as an alternative to tinplate Good lacquer adhesion, retortable, magnetic Always coated on both sides, with lacquer or film; check the coating system for the product
Aluminium Beverage ends, dry-food EOE, peel-off membranes and some rings Light, does not rust, easy to open On a steel can it makes a two-metal unit; retort suitability depends on the alloy and coating

Most food EOE in our range are offered in tinplate or TFS, and the same substrates are sold as sheet and scroll-cut for can makers. For a steel can, a steel end keeps the whole unit in one metal. That may matter once the PPWR recyclability grades apply, from 1 January 2030 at the earliest: the grade is assessed per packaging unit, and the design-for-recycling criteria have to cover all packaging components.


Matching the end to the product and the process

The shell and the opening type are only half of the specification. The other half is what touches the food and what the end has to survive.

Internal lacquer. It is chosen for the product. Acidic products such as tomatoes and some fruit need a lacquer that resists acid. Protein-rich products such as fish and meat can cause dark sulphide staining on steel, so ask whether the lacquer is sulphur-resistant. Ask which coating system the end carries and for a declaration of compliance under Regulation (EU) 2024/3190. The regulation restricts BPA and other hazardous bisphenols, and it covers, among other materials, varnishes and coatings, rubbers and printing inks, so the declaration should cover the lacquer, the sealing compound and any inks. “BPA-NI” on a data sheet means bisphenol A non-intent: BPA was not intentionally added.

Sealing compound. The compound in the curl seals the double seam and has to stay stable through the heat process. It is one of the components the PPWR substance statements should cover.

Heat process. State the process in the request: retort sterilisation (temperature, time, retort type, with or without overpressure), pasteurisation, hot fill or no heat process. A retortable end and a dry-food end can look identical. The difference is in the material, coatings and compound, and only the specification shows it.

Vacuum and pressure. Sterilised cans develop internal pressure during heating and vacuum after cooling. The end has to tolerate both without the panel deforming or the score opening. Ask the supplier for the pressure resistance of the end you are buying, not of the range in general.


Matching the end to the can and the seamer

Two ends with the same code from different suppliers can differ in curl diameter, countersink depth and compound placement, and the double seam depends on all three. The seamer chuck sits in the countersink, and the curl becomes the cover hook of the seam.

When you change supplier or end type, plan for:

  • the end drawing compared with your current end: curl diameter, countersink depth and panel profile;
  • a seaming trial on your own line;
  • seam teardowns and measurements on the trial cans, against your seam specification;
  • for a retorted product, a check of the cans after processing, not only after seaming.

The same applies to the can body. If you also buy cans, a supplier that provides cans and ends together can confirm the pairing on its side, but the trial on your seamer is still the proof.


EU rules that apply to ends

Ends are covered by the same rules as the rest of the can. Four points matter when you buy them.

Rule What it means for an easy-open end
Food contact: Regulation (EC) No 1935/2004 and, for coated ends, Regulation (EU) 2024/3190 A coated end must be accompanied by a written declaration of compliance at every marketing stage before retail (Article 8 of Regulation (EU) 2024/3190, referring to Article 16(1) of Regulation (EC) No 1935/2004)
Bisphenols: Regulation (EU) 2024/3190 Single-use articles made with BPA that met the earlier rules could be placed on the market until 20 July 2026. Two groups have until 20 January 2028: articles for preserving fruit or vegetables (other than juices and nectars) or fishery products, and articles where a varnish or coating made with BPA is on the exterior metal surface only. Articles placed on the market within these periods may still be filled and sealed during the 12 months after the period ends. Other hazardous bisphenols are restricted as well
Packaging: PPWR, Regulation (EU) 2025/40 The sum of lead, cadmium, mercury and hexavalent chromium resulting from substances in packaging or packaging components must not exceed 100 mg/kg (Article 5(4)); this applies to the end too, so the evidence has to cover it. The PFAS statement should cover the end’s lacquer, compound and any lubricants. The end is part of the packaging unit in your EU declaration of conformity, so a change of end calls for a re-assessment and, where needed, an updated declaration
CBAM, Regulation (EU) 2023/956 Today, easy-open ends, bottom ends and other closures, classified under CN 8309, are not on the CBAM list, while finished cans under CN 7310 and 7612 are. The Commission’s proposal COM(2025) 989 to extend CBAM to downstream goods from 1 January 2028 adds ex 8309 90 90, other stoppers, caps and lids of base metal containing steel or aluminium, which would bring can ends in. The proposal is still being negotiated

For the detail behind each point, see our articles on the BPA transition for can coatings, what the PPWR requires since 12 August 2026, the PPWR declaration of conformity and CBAM costs in metal packaging.


What to send a supplier when you ask for a quote

A complete request gets you a comparable quote and avoids a second round of questions.

Item Example
Size code and shape 300, round; or club 311
Can body it goes on Three-piece welded, 73 mm, your current can maker; or DRD
Opening type Full aperture, partial aperture or peel-off
Material Tinplate, TFS or aluminium; your preference if any
Product For example “tuna in oil”, “chopped tomatoes”, “wet pet food”, “milk powder”
Heat process Retort at 121 °C for 60 minutes, rotary, with overpressure; or no heat process
Internal and external coating Lacquer type, bisphenol requirements under Regulation (EU) 2024/3190, colour or print, tab colour
Seamer Make and model, current chuck and seaming set-up
Volumes Annual volume, call-off size, delivery country
Documents Declaration of compliance under 1935/2004 and 2024/3190; heavy-metals and PFAS statements under the PPWR; end drawing; batch coding

If you buy the end for an existing can, attach the drawing or a photo of the current end with its supplier code. If you are changing format at the same time, our guide to the PPWR declaration of conformity lists the documents your can and end suppliers have to provide.


Frequently asked questions

What does the number on an easy-open end mean?
It is the can diameter in the North American convention: the first digit is whole inches, the next two are sixteenths of an inch, measured over the double seam. A 300 end fits a can 3 inches across over the seam, which in Europe is called a 73 mm can. End makers publish a nominal diameter in millimetres next to the code, for example 72.9 mm for a 300 end, but that figure is not a conversion of the code.

Are ends with the same code from different suppliers interchangeable?
Not automatically. Curl diameter, countersink depth and compound placement can differ, and the double seam depends on them. Compare drawings and run a seaming trial with seam teardowns before switching.

What is the difference between a full-aperture and a partial-aperture end?
A full-aperture end opens the whole panel, so solid food can be removed. A partial-aperture end opens only part of it, for pouring, and suits liquids such as condensed milk or oils.

Can a peel-off end be retorted?
Yes, if it is a retortable version. Foil-membrane ends have traditionally been processed with overpressure in the retort to protect the membrane, and a newer design described in the literature withstands full heat processes without it. Check the process limits of the specific end against your retort.

Is an aluminium end on a steel can a problem?
It works technically. The can is then a two-metal unit. How the PPWR recyclability grades will treat such a combination depends on the design-for-recycling criteria the Commission has to adopt by 1 January 2028; the grades apply from 1 January 2030 at the earliest and are assessed per packaging unit. Check the combination with your supplier when you plan a change.

Do easy-open ends fall under CBAM?
Not today. Ends and other closures are classified under CN 8309, which is not in Annex I of the CBAM regulation, while finished cans under CN 7310 and 7612 are. The Commission has proposed adding ex 8309 90 90, which covers metal lids containing steel or aluminium, from 1 January 2028; the proposal is still being negotiated.

Which documents should come with an easy-open end?
A declaration of compliance under Regulation (EC) No 1935/2004 and Regulation (EU) 2024/3190, covering the coatings, sealing compound and inks; heavy-metals and PFAS statements to support your PPWR technical documentation; the end drawing; and a description of the batch coding.


Sources and primary references

This article is general guidance. End dimensions, process limits and coating systems differ between suppliers and products; the end drawing and the supplier’s specification govern.

Request Basket
Hello! How can we help you?